-
The S3 Saberhold is a custom designed bag specifically made for carrying illuminated sabers safely and conveniently. On the outside, there is a zipper compartment meant for storing blade plugs, hex keys, spare batteries and any other small objects needed for your saber. The Saberhold can be conveniently hand-carried with the handle at the side or could be slung across the shoulder. There is a buckle on each side of the bag for the sling strap to connect to, making it adjustable for a perfect fit no matter which shoulder you prefer to carry the bag with. Moving inside the bag, there are 2 long pockets; each designed to carry a single bladeless illuminated saber hilt and prevent it from getting scratched by other contents in the bag. Multiple blades can be stored in between these pockets and the Saberhold can be extended at the bottom so that a complete saber with a blade may also fit in it. The outer shell of the Saberhold is made from Cordura nylon which is well known for its durability especially against abrasions, tears and scuffs. Right under it is a plush layer of EVA foam padding to protect the illuminated sabers that are stored inside the bag. The sling strap is a 2″ industrial grade safety harness and all zippers & adjuster buckles are YKK. The S3 Saberhold represents a joint collaboration between Sabertrio and Greenroom136. The Rebel Edition features natural brown shades accented with orange stripes that were inspired by a particular pilot uniform. It is an exclusive design to Sabertrio. -
The S3 Saberhold is a custom designed bag specifically made for carrying illuminated sabers safely and conveniently. On the outside, there is a zipper compartment meant for storing blade plugs, hex keys, spare batteries and any other small objects needed for your saber. The Saberhold can be conveniently hand-carried with the handle at the side or could be slung across the shoulder. There is a buckle on each side of the bag for the sling strap to connect to, making it adjustable for a perfect fit no matter which shoulder you prefer to carry the bag with. Moving inside the bag, there are 2 long pockets; each designed to carry a single bladeless illuminated saber hilt and prevent it from getting scratched by other contents in the bag. Multiple blades can be stored in between these pockets and the Saberhold can be extended at the bottom so that a complete saber with a blade may also fit in it. The outer shell of the Saberhold is made from Cordura nylon which is well known for its durability especially against abrasions, tears and scuffs. Right under it is a plush layer of EVA foam padding to protect the illuminated sabers that are stored inside the bag. The sling strap is a 2″ industrial grade safety harness and all zippers & adjuster buckles are YKK. The S3 Saberhold represents a joint collaboration between Sabertrio and Greenroom136. The Rebel Edition features natural brown shades accented with orange stripes that were inspired by a particular pilot uniform. It is an exclusive design to Sabertrio. -
Out of stock
All-in-one STM32L4-based lightsaber electronics. It is small, feature-packed and 100% open source. This board retains all the features from the Teensy based designs, but are smaller and requires less work to put together. These are more advanced boards to use and it is recommended to read the detailed manual before use. Listing includes 1 x Proffieboard v2.2 and 1 x Micro SD Card. This is a new board with rolling updates. Board information and diagrams can be found here. These boards have been improved since the v1.5 and now has:Proffie Boards are both factory & SCF tested and confirmed 100% working prior to packing and shipping. When purchasing and installing a board, the customer does so at their own risk. Refunds will not be made for 'bricked' boards.- Breadboard compatible, no more tiny soldering pads
- Same size as before (1.3 x 0.7 inches)
- BATT- and GND are bridged by default (the bridge can be cut if desired)
- The components are a little farther away from the soldering pads
- The SD card sticks out more than before, hopefully making it easier to grab.
- FET pulldowns are grouned to BATT-, not GND
- Reverse polarity protection
- Beefier 5v power supply
- Able to completely cut power to the SD card (this *should* make deep sleep possible)
- The SD card power is also available on a pad, which could be used to cut power to bluetooth and displays during deep sleep.
- Uses resistor arrays to cut down on the number of components
- One less pad for neopixel data
- Neopixel LED Strip and Tri Cree LED Support.
- 44/22/11khz Audio.
- Touch Button Support.
- Multiple Blades And Effects With Different Presets For Each.
- Supports Both Monophonic and Polyphonic Sound Fonts
- Can Play Background Music With Other Sounds.
- Many Free Pins That Can Also Be Programmed For Other/Additional Features.
- Supports SmoothSwing! The Most Realistic Motion Algorithm For Sabers To Date!
- BATT+ – 2.6 to 4.5 volt input, drives everything except the LEDs
- BATT- – negative pad for LEDs, needs to be at same level as GND when both are connected. Note that there are two of them, which can be useful when driving many powerful LEDs.
- GND – ground for electronics except LEDs. Note that the two GND pads are interchangable and connected through the board.
- Button 1/2/3 – Hook up to closing buttons, or potentially touch buttons.
- Data 1 / ID – Normally used to measure the blade ID restor, and if it’s a neopixel blade, feed out neopixel data. For a fixed non-neopixel saber, it could be repurposed. Note that this pin has an internal 470 ohm resistor on it, so when hooked up to a neopixel blade, it does not need any resistors.
- Data 2-3 – additional neopixel data outputs, or free for other purposes.
- Data4/Dac – noeopixel data output, free, or audio DAC output
- LED 1-6 – Hooks up to negative side of LED (positive side of LED hooks up directly to battery.) These pads can handle up to 30 volts.
- SD Power – FET-controlled 3.3v. can be used to power down bluetooth and displays in low-power mode.
- SDA, SCL – these pins are used to communicate with the gyro and accelerometer chip.
- 5v – generated by the proffieboard, normally it’s only on when sound is playing.
- 3.3v – generated by the proffieboard.
- SWDIO, SWDCLK – can be hooked up to a ST-LINK device and lets you debug programs running on the proffieboard.
-
The new NeoCree LED strip to Tri Cree RGRb XPE-2 conversion module. These have been designed and produced by Warsabers and ShtokCustomWorx to conveniently allow users to seamlessly convert their neopixel lightsaber builds, that use pogo pin PCB connectors, to an RGB ‘in-hilt’ LED system. -
Complete blade 1" / 25.4mm OD 3.2mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard -
Out of stock
Complete blade 1" / 25.4mm OD 3.2mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard -
Complete blade 1" / 25.4mm OD 3.0mm thick walled Polycarbonate tube Internal diffusion with wrapped film diffuser and a milky polycarb' tube and tip. Reflective disc on the base of the shouldered tip is standard. This is the parabolic tip (more pointed) version. -
Out of stock
Complete blade 1" / 25.4mm OD 1.8mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard
-
Out of stock
Complete blade 1" / 25.4mm OD 1.8mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard
-
First off, apologies for the price of cells at the moment. Supply chain issues have killed off the boutique NZ suppliers and we're having to import from overseas in small quantities via DHL / Fedex (Haz rated services). We prioritize cells for our installs, but occasionally have a spare or two to list from our regular orders. Button top model ideal for soldering. Protected circuit. rated for 15A continuous discharge, making them suitable for NeoPixel installs. Price is per cell. Note: Our protected 18650 stock is usually too long for the single 18650 cell holders we have in stock (due to the extra length added by the protection PCB). Chat to us prior to ordering & we'll test fit. -
Out of stock
A durable one piece design. This part can be used to combine various Adaptive Saber Parts or two Saberforge hilts together to make a staff. Available in a weathered finish. Length: 1.75in (4.445cm) -
Out of stock
Red/Red/White Cree XP-E2 CopperNova Red Cree Forward Voltage @1000mA = 2.65V White Cree Forward Voltage @1000mA = 3.15V Triple Cree XP-E2 mounted on a SinkPAD-ll copper star providing a direct thermal path between the LED and Star. The most suitable, closest available resistors will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator. -
Green/Green/White Cree XP-E2 CopperNova Green Cree Forward Voltage @1000mA = 3.7V White Cree Forward Voltage @1000mA = 3.15V Triple Cree XP-E2 mounted on a SinkPAD-ll copper star providing a direct thermal path between the LED and Star. The most suitable, closest available resistors will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
Blue/Blue/White Cree XP-E2 CopperNova Blue Cree Forward Voltage @1000mA = 3.4V White Cree Forward Voltage @1000mA = 3.15V Triple Cree XP-E2 mounted on a SinkPAD-ll copper star providing a direct thermal path between the LED and Star. The most suitable, closest available resistors will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
