Loading...
  • Plecter Labs Power Xtender™ Ver 2.0 Miniature electronic circuit designed to drive/switch a high load (LED, rumbling motor, relay) when the low voltage/current output from our electronic boards does not allow it. Drives for instance a 3.6V LED from a Blaster Core™ board or a luxeon from the Flash on Clash™ output of Crystal Focus™. Refer to the Petit Crouton user's manual for further details about the use of this module. NEW : Now with embedded SMD 2512 resistor footprint. Saves space when using the Power Xtender™ to drive the Flash On Clash ™. Use with 2 watt 2512 thick carbon film resistor. Dimensions : 0.55"x0.36" Input voltage : 0-5 volts max. Switches at 3.3V Output voltage/current : 12V / 1.5A
  • Sale!

    Orange CREE XP-E LED / 3W

    Original price was: NZ$19.99.Current price is: NZ$9.99.
    Max Forward Voltage 2.5V Max Current 1000mAh The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
  • ## WORKS WITH ANY SABER USING A 2.1MM RECHARGE PORT & SINGLE LI-ION CELL ## This is the charger used to recharge an illuminated saber that has a 2.1mm recharge port in its electronic setup. It's a generic charger from an OEM supplier. We've sourced and tested these and they do the job nicely. Input Voltage : AC 100-240V (Worldwide AC Input) Input Frequency : 50-60Hz Output : 4.2V 1A  5.5mm*2.1mm Over Voltage Protection Over Heat Protection
  • A quick Google has suggested these thread sizes: Metric: 7.7 mm OD, thread root diameter is 6.9 mm × 0.794 mm pitch.
  • Momentary to latching converter 2.2 to 16V Allows for the use of a momentary switch in a latching circuit. Specifications •Dimensions: 0.6" x 0.7" x 0.12" (without header pins installed) •Operating voltage: 2.2-16V •Maximum current: 6A •Draws very little current in off state (typically under 0.01 μA)
  • Micro Deans connectors. Same connectors used in Saberforge QC hilts.
  • This is a seriously nice Mandalorian Vibroblade model. Printed in 2x parts, it assembles to 29.5cm in length. We print at 0.15mm layer height and 80% infill (for weight). At that size, it's a swift print of just under 6 hours on the machine. This is a bare plastic print which looks great but would also lend itself to additional cosmetic work.

    How it Works

    Whilst we're ultra-nerdy enough to run a fine suite of well maintained 3D printers, our CAD skills are a work in progress. We're predominantly a 3D printing service and only charge for machine time, which is usually only NZ$3.00 p.h.! Our little 3D print store is simply an example of some of the items we can print for you from well know sources such as www.ThingiVerse.com. It's a great source of 3D Printer files and we invite you to explore. If you see something you like, just come back to us for a print quote. ThingiVerse designs are covered by a range of different licenses from 'free to do what you want' Creative Commons licenses right through to 'non-commercial' clauses. For anything other than CC, we'll work with you to ensure no distribution licenses are breached (usually by simply asking the designer if we can print the item on your behalf). Easy as that. So if you're looking for a design we don't have listed as an example, just contact us.

    File Source

    Files : www.thingiverse.com/thing:4004452 Designer : www.thingiverse.com/Filament_3d_Printing This item is covered by the Creative Commons - Attribution license We tip the designers! Even though the example designs we use fall under Creative Commons, we still like to give credit where credit is due so always endeavour to 'tip' the designer for their work via (for example) the ThingiVerse 'tip designer' feature. We aim for a 10% tip (or the nearest equivalent on the drop-down). If the designer doesn't accept tips, 10% goes to a local charity!
  • M4 thread for sabers designed pretty much anywhere else in the world other than the US. These will kit LGT, TXQ & many others. Please feel free to check with us re: the correct thread for your saber.
  • This will hold most light sabers up to 4.5cm in diameter - the relief in the bottom portion is cut out to allow for wall mount power to your saber or for sound - the upper part will hold a 1" (25.4mm) blade securely enough that it wont fall out, but easy enough to take off the wall in case of Imperial entanglements. This is a bare plastic print.

    How it Works

    Whilst we're ultra-nerdy enough to run a fine suite of well maintained 3D printers, our CAD skills are a work in progress. We're predominantly a 3D printing service and only charge for machine time, which is usually only NZ$3.00 p.h.! Our little 3D print store is simply an example of some of the items we can print for you from well know sources such as www.ThingiVerse.com. It's a great source of 3D Printer files and we invite you to explore. If you see something you like, just come back to us for a print quote. ThingiVerse designs are covered by a range of different licenses from 'free to do what you want' Creative Commons licenses right through to 'non-commercial' clauses. For anything other than CC, we'll work with you to ensure no distribution licenses are breached (usually by simply asking the designer if we can print the item on your behalf). Easy as that. So if you're looking for a design we don't have listed as an example, just contact us.

    File Source

    Files : www.thingiverse.com/thing:3023020 Designer : www.thingiverse.com/Elloel/about This item is covered by the Creative Commons - Attribution license We tip the designers! Even though the example designs we use fall under Creative Commons, we still like to give credit where credit is due so always endeavour to 'tip' the designer for their work via (for example) the ThingiVerse 'tip designer' feature. We aim for a 10% tip (or the nearest equivalent on the drop-down). If the designer doesn't accept tips, 10% goes to a local charity!
  • This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. Hilt:
    • KR Sabers Flagship in Tactical Black
    Install:
    • Proffie V2.2 with approx' 8 quality, open source sound fonts.
    • Sabertrio Copper based heatsink and high performance XP-E2 Tri Cree LED
    • Correct grade wire throughout
    • Single 12mm non-illuminated red anodised switch. Saber runs single switch logic.
    • Nix - 3D Printed Chassis
    • Chassis mounted kill switch
    • High capacity 18650 cell (protected)
    • KR Sabers 24mm Bass Speaker
    Extra Touches: Genuine slightly aged red leather. Hand stitched with a cross-stich and backed with a small touch of adhesive to minimise any drifting. External charger (for the cell) & blade are optional.
  • This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:
    • KR Sabers Flagship in Tactical Green
    Install:
    • Proffie V2.2 with approx' 8 quality, open source sound fonts.
    • ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
    • Correct grade silicon wire throughout
    • Single KR Sabers 12mm Illuminated Cog Switch. Saber runs single switch logic).
    • Goth3D - 3D Printed Chassis
    • Chassis mounted kill switch
    • High capacity 18650 cell (protected)
    • KR Sabers 28mm Bass Speaker
    Extra Touches: Genuine slightly aged brown leather. Hand stitched with a cross-stich and backed with a small touch of adhesive to minimise any drifting. External charger (for the cell) & neopixel blade are optional.
  • This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:
    • KR Sabers Flagship in Tactical Green
    Install:
    • Proffie V2.2 with approx' 12 quality open source sound fonts.
    • ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
    • Correct grade silicon wire throughout
    • KR Sabers Duoswitch. A PWR & AUX tactile switch combined into one 12mm 'rocker' design.
    • 3D Printed Chassis
    • High capacity 18650 cell (unprotected)
    • KR Sabers 28mm Bass Speaker
    Extra Touches: Genuine red leather with a subtle stamped reptile design. Hand stitched with a cross-stich and backed with a small touch of adhesive to minimise any drifting. External charger (for the cell) & neopixel blade are optional.

Title