-
This is the SHORT pin option. The long pin version are the standard choice unless you are installing in hilts with shallow emitters (i.e. thin neck models), where you would want this short pin version. If you are not already using a chassis with a dedicated recess, you will likely need a PCB holder. Kit comes un-assembled. You need to solder your own pins into the PCB. The manual can be found here. -
This is the LONG pin option. Long pins are the standard choice unless you are installing in hilts with shallow emitters (i.e. thin neck models), where you would want a short pin version. If you are not already using a chassis with a dedicated recess, you will likely need a PCB holder AND a Lens Cover (to better support the pins. Kit comes un-assembled. You need to solder your own pins into the PCB. The manual can be found here. -
ShtokCustomWorx NPXL V3 LED Strip PCB Holder. This is the hilt side and for 1" emitters. It is also designed for the both the long pins AND short pins. Note that, for use with Long pins, you will need to purchase an additional lens cover. This is required for use with the long pin PCB. If you do not use a lens cover when using the long pins PCB you can risk bending or damaging your pins. -
The ShtokCustomWorx NPXL V3 PCB Lens Cover. This is the lens diffusion cover for the V3 PCB holders. Note that the holder is press fit in. -
The new NeoCree LED strip to Tri Cree RGRb XPE-2 conversion module. These have been designed and produced by Warsabers and ShtokCustomWorx to conveniently allow users to seamlessly convert their neopixel lightsaber builds, that use pogo pin PCB connectors, to an RGB ‘in-hilt’ LED system. -
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- KR Sabers Flagship in Tactical Green
- Proffie V2.2 with approx' 12 quality open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- KR Sabers Duoswitch. A PWR & AUX tactile switch combined into one 12mm 'rocker' design.
- 3D Printed Chassis
- High capacity 18650 cell (unprotected)
- KR Sabers 28mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- KR Sabers Flagship in Tactical Green
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- Single KR Sabers 12mm Illuminated Cog Switch. Saber runs single switch logic).
- Goth3D - 3D Printed Chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- KR Sabers 28mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. Hilt:- KR Sabers Flagship in Tactical Black
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- Sabertrio Copper based heatsink and high performance XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 12mm non-illuminated red anodised switch. Saber runs single switch logic.
- Nix - 3D Printed Chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- KR Sabers 24mm Bass Speaker
-
Out of stock
This is a brand new saber expertly installed with carefully selected, complimentary quality components. It is a grade B hilt which means it has small cosmetic flaws. On this hilt, flaws include a minor ding on the edge of the emitter. There may be other smaller cosmetic flaws. This is sold un-rectified, but could be touched up with nail polish or paint / pen. These small cosmetic niggles saves you some serious $$$. The red is difficult to capture, but it's a slightly deeper red than the images portray and is translucent (see through). The images with the white background are more representative than the main image. Should note, that we consider powder coated hilts like this as 'show ponies'. Powder coat can chip under impact. It is lovingly installed in-house with factory components. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- SaberTrio Vahlken Dolovite (grade B)
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- SaberTrio factory delrin chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- SaberTrio 22mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. It is a grade B hilt which means it has small cosmetic flaws. On this hilt, flaws include minor dings on the back edge of the emitter. There may be other smaller cosmetic flaws. This is sold (kinda) un-rectified, but could be touched up with nail polish or paint / pen. I've demonstrated my favourite technique for dealing with powder coat dings, which is simply using a permanent marker dabbed into the chip to simulate carbon scoring. You get that mix of bare metal, black + the original finish. These small cosmetic niggles saves you some serious $$$. The red is difficult to capture, but it's a slightly deeper red than the images portray and is semi-translucent (see through). The images with the white background are more representative than the main image. Should note, that we consider powder coated hilts like this as 'show ponies', unless you're happy to live with the dings just to have a unique saber. Powder coat can chip under impact. It is lovingly installed in-house with factory components. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. You cannot get an RGB baselit Proffie V2.2 install from the factory. Hilt:- SaberTrio Vahlken Dolovite (grade B)
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- TCSS Copper based heatsink and high performance SaberTrio XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 16mm non-illuminated red switch. Saber runs single switch logic. Aux switch is a dummy.
- SaberTrio factory delrin chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- SaberTrio 22mm Bass Speaker
-
Sale!
Max Forward Voltage 3.6V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator. -
JST Female connector 26AWG Green 200mm long -
JST male connector 26AWG Green 200mm long -
Sale!
Max Forward Voltage 2.5V Max Current 1000mAh The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
