Loading...
  • Complete blade 1" / 25.4mm OD 3.2mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard
  • Out of stock
    Complete blade 1" / 25.4mm OD 1.8mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard
  • Out of stock
    Complete blade 1" / 25.4mm OD 3.2mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard
  • Out of stock
    Sale!

    Saberforge Forsaken #005 – Ready to Ship (RTS)

    Original price was: NZ$435.00.Current price is: NZ$300.00.
    This is a brand new saber expertly tweaked to take a modded Nexus Sabers Xeno3 Pixel Core + some other complimentary quality components. Includes BLADE!! It's a nice prior model Saberforge Forsaken (new) running a Xeno3Pixel board (non Bluetooth Version) in an original modded chassis, with a ShtokCustomWork short pin PCB in the emitter. It takes a standard 5V 2.1mm plug for charging. LED switch for standard menu operation. A gazillion sound fonts (30 something) & effects. Certainly not a dueller in any sense of the word (no neopixel is) but a great cosplay / play-piece. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:
    • Saberforge Forsaken (prior model)
    Install:
    • Modded Nexus Sabers (LGT) Xeno3Pixel core.
    • ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
    • External 2.1mm Recharge Port (wired for a 5v USB Charge cable)
    • 12mm Illuminated Switch.
    • High capacity Nexus 18650 cell (protected)
    • This is a NON BLUETOOTH version of the board so you can't use it with the app.
    Extra Touches: USB 5v Charging cable. USB 5v Charging Brick 37" Neopixel Nexus  Blade INCLUDED
  • Out of stock
    A durable one piece design. This part can be used to combine various Adaptive Saber Parts or two Saberforge hilts together to make a staff. Available in a weathered finish. Length: 1.75in (4.445cm)
  • Out of stock
    A durable one piece design. This part can be used to combine various Adaptive Saber Parts or two Saberforge hilts together to make a staff. Available in a standard or weathered finish (standard pictured). Length: .8in (2.032cm)
  • Out of stock
    Sale!

    Saberforge Adamant

    Original price was: NZ$199.00.Current price is: NZ$149.00.
    The hilt is machined by a professional blade smith, with tireless care given to every detail of it's construction, this saber is a work of art.
  • Sale!

    Royal Blue CREE XP-E LED / 3W

    Original price was: NZ$19.99.Current price is: NZ$9.99.
    Max Forward Voltage 3.6V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
  • Sale!

    Red CREE XP-E LED / 3W

    Original price was: NZ$19.99.Current price is: NZ$9.99.
    Max Forward Voltage 2.4V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
  • Out of stock
    All-in-one STM32L4-based lightsaber electronics. It is small, feature-packed and 100% open source. This board retains all the features from the Teensy based designs, but are smaller and requires less work to put together. These are more advanced boards to use and it is recommended to read the detailed manual before use. Listing includes 1 x Proffieboard v2.2 and 1 x Micro SD Card. This is a new board with rolling updates. Board information and diagrams can be found here. These boards have been improved since the v1.5 and now has:
    • Breadboard compatible, no more tiny soldering pads
    • Same size as before (1.3 x 0.7 inches)
    • BATT- and GND are bridged by default (the bridge can be cut if desired)
    • The components are a little farther away from the soldering pads
    • The SD card sticks out more than before, hopefully making it easier to grab.
    • FET pulldowns are grouned to BATT-, not GND
    • Reverse polarity protection
    • Beefier 5v power supply
    • Able to completely cut power to the SD card (this *should* make deep sleep possible)
    • The SD card power is also available on a pad, which could be used to cut power to bluetooth and displays during deep sleep.
    • Uses resistor arrays to cut down on the number of components
    • One less pad for neopixel data
    It retains it’s legacy features:
    • Neopixel LED Strip and Tri Cree LED Support.
    • 44/22/11khz Audio.
    • Touch Button Support.
    • Multiple Blades And Effects With Different Presets For Each.
    • Supports Both Monophonic and Polyphonic Sound Fonts
    • Can Play Background Music With Other Sounds.
    • Many Free Pins That Can Also Be Programmed For Other/Additional Features.
    • Supports SmoothSwing! The Most Realistic Motion Algorithm For Sabers To Date!
    Technical info:
    • BATT+ – 2.6 to 4.5 volt input, drives everything except the LEDs
    • BATT- – negative pad for LEDs, needs to be at same level as GND when both are connected. Note that there are two of them, which can be useful when driving many powerful LEDs.
    • GND – ground for electronics except LEDs. Note that the two GND pads are interchangable and connected through the board.
    • Button 1/2/3 – Hook up to closing buttons, or potentially touch buttons.
    • Data 1 / ID – Normally used to measure the blade ID restor, and if it’s a neopixel blade, feed out neopixel data. For a fixed non-neopixel saber, it could be repurposed. Note that this pin has an internal 470 ohm resistor on it, so when hooked up to a neopixel blade, it does not need any resistors.
    • Data 2-3 – additional neopixel data outputs, or free for other purposes.
    • Data4/Dac – noeopixel data output, free, or audio DAC output
    • LED 1-6 – Hooks up to negative side of LED (positive side of LED hooks up directly to battery.) These pads can handle up to 30 volts.
    • SD Power – FET-controlled 3.3v. can be used to power down bluetooth and displays in low-power mode.
    • SDA, SCL – these pins are used to communicate with the gyro and accelerometer chip.
    • 5v – generated by the proffieboard, normally it’s only on when sound is playing.
    • 3.3v – generated by the proffieboard.
    • SWDIO, SWDCLK – can be hooked up to a ST-LINK device and lets you debug programs running on the proffieboard.
    PLEASE NOTE: These boards are fully factory tested and approved prior to shipping. It is highly recommended to have a professional saber builder install this board. If you wish to install yourself; it is at your own risk. If you fry the board, it's on you. If there are any technical issues with the installation of the board please get in touch and we can forward you various information including groups and forums where troubleshooting can take place.

Title