-
The ShtokCustomWorx NPXL V3 PCB Lens Cover. This is the lens diffusion cover for the V3 PCB holders. Note that the holder is press fit in. -
28mm OD x 10mm tall. 8 ohm speaker. Perfect for the Saberforge Chassis. These are currently KR Sabers stock. NOT suitable for Sabertrio sabers, that require a recessed diaphragm (VECO 28mm speakers) or the recently released 22mm SaberTrio speakers + mount. -
Plecter Labs Power Xtender™ Ver 2.0 Miniature electronic circuit designed to drive/switch a high load (LED, rumbling motor, relay) when the low voltage/current output from our electronic boards does not allow it. Drives for instance a 3.6V LED from a Blaster Core™ board or a luxeon from the Flash on Clash™ output of Crystal Focus™. Refer to the Petit Crouton user's manual for further details about the use of this module. NEW : Now with embedded SMD 2512 resistor footprint. Saves space when using the Power Xtender™ to drive the Flash On Clash ™. Use with 2 watt 2512 thick carbon film resistor. Dimensions : 0.55"x0.36" Input voltage : 0-5 volts max. Switches at 3.3V Output voltage/current : 12V / 1.5A -
Out of stock
28mm OD x 12mm tall. 4 ohm speaker. Perfect for the Saberforge Chassis. Louder and deeper bass than the standard 2W speaker. -
Out of stock
20mm OD x 12mm tall. 4 ohm speaker. Louder and deeper bass than the standard 2W speaker. -
The MC1 features the same safety and triple mode charging that all of the current generation Xtar chargers have. It gets its power from a USB cable, plugged into a car adapter, wall adapter, power bank, solar charger, or your computer. Features: - Reverse-polarity and short circuit protection circuit - Three-stage charging and 0V battery activation - Micro USB port to supply power for the charger - Adopts IC temperature monitor to avoid over heat - Small charge current when start to charge - Compact size portable - Low heat design Apply to: 10440/14500/14650/16340/17500/17670/18350/18500/18650/18700/ 22650/ 25500/26650 3.6V/3.7V Li-ion batteries -
Heatsink module for 1" / 25mm ID tubes. Comes with centre hole and the 6x wire runs are milled to the edge of the copper heatsink. -
Heatsink module for 7/8" / 22.5mm ID tubes. .875" OD x .75" long Heatsink module with center hole. These are designed to fit the Parks/Korbanth sabers such as the Graflex 2.0 These are only made to be used with the tri cree/rebel lens holder and a slightly modified star base. -
## WORKS WITH ANY SABER USING A 2.1MM RECHARGE PORT & SINGLE LI-ION CELL ## This is the charger used to recharge an illuminated saber that has a 2.1mm recharge port in its electronic setup. It's a generic charger from an OEM supplier. We've sourced and tested these and they do the job nicely. Input Voltage : AC 100-240V (Worldwide AC Input) Input Frequency : 50-60Hz Output : 4.2V 1A 5.5mm*2.1mm Over Voltage Protection Over Heat Protection -
Out of stock
Covertec belt clip -
Chassis to fit a Saberforge lightsaber hilt. This is made to hold a 18650 battery and 28mm speaker which are not included. Has a flat top surface to which to attach a range of boards. We print these to order, often tuning the length to suit your electronics cavity (leaving enough for wires but no 'rattly' gaps). Variety of colours available. Note your preference(s) in the order notes at checkout. No RCP hole, but there is a clever way to fit one on a longer chassis :) It will work with the Premium or Bass speaker -
Chassis to fit a SaberTrio / Ultrasabers / MHS V1. This is made to hold a 18650 battery, sound module, and speaker which are not included. Will take a wide range of boards. It will work with the Premium or Bass speaker. This is a design distributed under the Creative Commons license. in accordance with the CC license, credit can be found at https://www.thingiverse.com/thing:2941974
