-
Out of stock
This is a brand new saber expertly installed with carefully selected, complimentary quality components. It is a grade B hilt which means it has small cosmetic flaws. On this hilt, flaws include a minor ding on the edge of the emitter. There may be other smaller cosmetic flaws. This is sold un-rectified, but could be touched up with nail polish or paint / pen. These small cosmetic niggles saves you some serious $$$. The red is difficult to capture, but it's a slightly deeper red than the images portray and is translucent (see through). The images with the white background are more representative than the main image. Should note, that we consider powder coated hilts like this as 'show ponies'. Powder coat can chip under impact. It is lovingly installed in-house with factory components. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- SaberTrio Vahlken Dolovite (grade B)
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- SaberTrio factory delrin chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- SaberTrio 22mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- KR Sabers Flagship in Tactical Green
- Proffie V2.2 with approx' 12 quality open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- KR Sabers Duoswitch. A PWR & AUX tactile switch combined into one 12mm 'rocker' design.
- 3D Printed Chassis
- High capacity 18650 cell (unprotected)
- KR Sabers 28mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- KR Sabers Flagship in Tactical Green
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- Single KR Sabers 12mm Illuminated Cog Switch. Saber runs single switch logic).
- Goth3D - 3D Printed Chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- KR Sabers 28mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. Hilt:- KR Sabers Flagship in Tactical Black
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- Sabertrio Copper based heatsink and high performance XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 12mm non-illuminated red anodised switch. Saber runs single switch logic.
- Nix - 3D Printed Chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- KR Sabers 24mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. It is a grade B hilt which means it has small cosmetic flaws. On this hilt, flaws include minor dings on the back edge of the emitter. There may be other smaller cosmetic flaws. This is sold (kinda) un-rectified, but could be touched up with nail polish or paint / pen. I've demonstrated my favourite technique for dealing with powder coat dings, which is simply using a permanent marker dabbed into the chip to simulate carbon scoring. You get that mix of bare metal, black + the original finish. These small cosmetic niggles saves you some serious $$$. The red is difficult to capture, but it's a slightly deeper red than the images portray and is semi-translucent (see through). The images with the white background are more representative than the main image. Should note, that we consider powder coated hilts like this as 'show ponies', unless you're happy to live with the dings just to have a unique saber. Powder coat can chip under impact. It is lovingly installed in-house with factory components. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. You cannot get an RGB baselit Proffie V2.2 install from the factory. Hilt:- SaberTrio Vahlken Dolovite (grade B)
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- TCSS Copper based heatsink and high performance SaberTrio XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 16mm non-illuminated red switch. Saber runs single switch logic. Aux switch is a dummy.
- SaberTrio factory delrin chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- SaberTrio 22mm Bass Speaker
-
Out of stock
This is a brand new saber expertly installed with carefully selected, complimentary quality components. It is a grade B hilt which means it has small cosmetic flaws. On this hilt, flaws include a minor blemish in the anodising on the grip, about 1/4 way up from the pommel & the tiniest of dings in the emitter. These small cosmetic niggles saves you some serious $$$. It is lovingly installed in-house with factory components. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. You cannot get an RGB baselit Proffie V2.2 install from the factory. Hilt:- SaberTrio Skylar (grade B)
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- Sabertrio Copper based heatsink and high performance XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 16mm non-illuminated gold anodised switch. Saber runs single switch logic. Aux switch is a dummy.
- SaberTrio factory delrin chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- SaberTrio 22mm Bass Speaker
-
Out of stock
This is a brand new saber expertly installed with carefully selected, complimentary quality components. It is a grade B hilt which means it has small cosmetic flaws. On this hilt, flaws include a couple of powder coat sections that 'could be better'. There may be other smaller cosmetic flaws. These small cosmetic niggles saves you some serious $$$. Colour accents nod to our favourite universe bounty hunter. Should note, powder coat sections can chip under impact. It is lovingly installed in-house with factory components. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. You cannot get an RGB baselit Proffie V2.2 install from the factory. Hilt:- SaberTrio Vahlken Dolovite (grade B)
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- Sabertrio Copper based heatsink and high performance XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 16mm non-illuminated green switch. Saber runs single switch logic. Aux switch is a dummy.
- SaberTrio factory delrin chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- SaberTrio 22mm Bass Speaker
-
Out of stock
Sulphur City Foundry is the official SaberTrio representative for New Zealand and Australia. (Content & images courtesy of https://sabertrio.com). With its three distinctive claws, uniquely shaped windows and highly detailed emitter, the Sabertrio Reaver easily distinguishes itself from the rest of the pack through its aggressive, but also elaborate design. The dual chokes and large lower section provides space for a strong grip. The Reaver is 300mm (12.0″) long and has an average diameter of 36mm (1.42″). -
Out of stock
Sulphur City Foundry is the official SaberTrio representative for New Zealand and Australia. (Content & images courtesy of https://sabertrio.com). The Sabertrio Vahklen illuminated saber is designed to exude aggressiveness. It only takes a glance to recognize its distinctive features; an edgy octagon profile with 16 large windows that lights up menacingly when the saber is ignited. Its handle, which averages 35mm (1.38”) in diameter, has 4 extruded rings that provides a very solid and comfortable grip. The Vahlken is 287mm (11.3”) long and has an average diameter of 36mm (1.42”). -
Out of stock
Sulphur City Foundry is the official SaberTrio representative for New Zealand and Australia. (Content & images courtesy of https://sabertrio.com). With the Sabertrio Aeryn, comes forth one of the most iconic saber design elements in the galaxy; the brass thin-neck. Averaging at a mere 15mm (0.6″) in diameter, it functions as the perfect choke while remaining strong enough for dueling. The grenade-inspired grip adds a whole new level of detailing and pays homage to the saber of which it drew inspiration from. The Aeryn is 285mm (11.2″) long and has an average diameter of 36mm (1.42″). -
Out of stock
Sulphur City Foundry is the official SaberTrio representative for New Zealand and Australia. (Content & images courtesy of https://sabertrio.com). The Sabertrio Skylar illuminated saber is designed to be authentic and true to the elegant weapon that it was inspired from. The slanted emitter with 3 window slits on each side emanates an aggressive aura while the double chokes ensures are a very strong grip without sacrificing maneuverability. The blade is released or locked into the saber with an exposed retention screw that can be hand tightened. The Skylar is 289.5mm (11.4″) long which allows it to be wielded comfortably with two hands and has an average diameter of 36mm (1.42″). -
Out of stock
Sulphur City Foundry is the official SaberTrio representative for New Zealand and Australia. (Content & images courtesy of https://sabertrio.com). The Sabertrio Mirah illuminated saber, at its heart, is a duelist’s saber. With a thin, streamlined profile and light body, Mirah is as nimble as it is comfortable to wield. Accentuating it’s design is the curved slanted emitter and stylized horizontal window slits. Unique to it is the pommel’s removable end cap which allows the wielder to attach his/her own sword tassel to the saber, further personalizing it. Mirah is 264.5mm (10.4″) long which allows it to be wielded comfortably with both single hand and two hands and has an average diameter of 35mm (1.37″). -
Out of stock
Sulphur City Foundry is the official SaberTrio representative for New Zealand and Australia. (Content & images courtesy of https://sabertrio.com). Introducing the first illuminated saber by Sabertrio, the Arclyte. Designed to be versatile, it could be wielded with one hand, both hands or when a shorter blade is attached, as an off hand. The knurling on the hilt ensures a strong but comfortable grip and the choke allows the saber to be spun easily. The Arclyte is 260mm (10.25″) long and has an average diameter of 37mm (1.45″) -
Sale!Out of stock
This is a brand new saber expertly tweaked to take a modded Nexus Sabers Xeno3 Pixel Core + some other complimentary quality components. Includes BLADE!! It's a nice prior model Saberforge Forsaken (new) running a Xeno3Pixel board (non Bluetooth Version) in an original modded chassis, with a ShtokCustomWork short pin PCB in the emitter. It takes a standard 5V 2.1mm plug for charging. LED switch for standard menu operation. A gazillion sound fonts (30 something) & effects. Certainly not a dueller in any sense of the word (no neopixel is) but a great cosplay / play-piece. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- Saberforge Forsaken (prior model)
- Modded Nexus Sabers (LGT) Xeno3Pixel core.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- External 2.1mm Recharge Port (wired for a 5v USB Charge cable)
- 12mm Illuminated Switch.
- High capacity Nexus 18650 cell (protected)
- This is a NON BLUETOOTH version of the board so you can't use it with the app.
-
Sale!Out of stock
The hilt is machined by a professional blade smith, with tireless care given to every detail of it's construction, this saber is a work of art.
