-
Sale!
Max Forward Voltage 3.6V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator. -
Sale!
Max Forward Voltage 3.6V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
Sale!
Max Forward Voltage 2.4V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
JST Female connector 26AWG Green 200mm long -
JST male connector 26AWG Green 200mm long -
JST Female connector 26AWG Blue White 200mm long -
JST Male connector 26AWG Blue White 200mm long -
Single 18650 battery holder. Please note... these can be extremely tight when combined with protected 18650 cells. For example, our current protected cells are too long to comfortably fit. They are fine with unprotected cells or protected cells no longer than 69mm. -
Out of stock
Covertec belt clip -
Chassis to fit a Saberforge lightsaber hilt. This is made to hold a 18650 battery and 28mm speaker which are not included. Has a flat top surface to which to attach a range of boards. We print these to order, often tuning the length to suit your electronics cavity (leaving enough for wires but no 'rattly' gaps). Variety of colours available. Note your preference(s) in the order notes at checkout. No RCP hole, but there is a clever way to fit one on a longer chassis :) It will work with the Premium or Bass speaker -
28mm OD x 10mm tall. 8 ohm speaker. Perfect for the Saberforge Chassis. These are currently KR Sabers stock. NOT suitable for Sabertrio sabers, that require a recessed diaphragm (VECO 28mm speakers) or the recently released 22mm SaberTrio speakers + mount. -
Micro Deans connectors. Same connectors used in Saberforge QC hilts. -
Sale!
Max Forward Voltage 2.4V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
Sale!
Max Forward Voltage 2.5V Max Current 1000mAh The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
Sale!
Max Forward Voltage 3.5V Max Current 1000mA Arctic Blue is blue with a hint of green. The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
Plecter Labs Power Xtender™ Ver 2.0 Miniature electronic circuit designed to drive/switch a high load (LED, rumbling motor, relay) when the low voltage/current output from our electronic boards does not allow it. Drives for instance a 3.6V LED from a Blaster Core™ board or a luxeon from the Flash on Clash™ output of Crystal Focus™. Refer to the Petit Crouton user's manual for further details about the use of this module. NEW : Now with embedded SMD 2512 resistor footprint. Saves space when using the Power Xtender™ to drive the Flash On Clash ™. Use with 2 watt 2512 thick carbon film resistor. Dimensions : 0.55"x0.36" Input voltage : 0-5 volts max. Switches at 3.3V Output voltage/current : 12V / 1.5A -
Out of stock
Price is for one. -
The MC1 features the same safety and triple mode charging that all of the current generation Xtar chargers have. It gets its power from a USB cable, plugged into a car adapter, wall adapter, power bank, solar charger, or your computer. Features: - Reverse-polarity and short circuit protection circuit - Three-stage charging and 0V battery activation - Micro USB port to supply power for the charger - Adopts IC temperature monitor to avoid over heat - Small charge current when start to charge - Compact size portable - Low heat design Apply to: 10440/14500/14650/16340/17500/17670/18350/18500/18650/18700/ 22650/ 25500/26650 3.6V/3.7V Li-ion batteries -
Out of stock
28mm OD x 12mm tall. 4 ohm speaker. Perfect for the Saberforge Chassis. Louder and deeper bass than the standard 2W speaker. -
24mm OD 4 ohm speaker. Perfect for the 7 Chambers Chassis (with a bit of trimming). Price is for 1x speaker.
