-
Complete blade 1" / 25.4mm OD 3.2mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard -
Out of stock
Complete blade 1" / 25.4mm OD 1.8mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard -
Out of stock
Complete blade 1" / 25.4mm OD 3.2mm medium-thick walled Polycarbonate tube Dual diffused with wrapped film diffuser and a milky polycarb'. Reflective disc on the base of the shouldered tip is standard
-
Sale!Out of stock
This is a brand new saber expertly tweaked to take a modded Nexus Sabers Xeno3 Pixel Core + some other complimentary quality components. Includes BLADE!! It's a nice prior model Saberforge Forsaken (new) running a Xeno3Pixel board (non Bluetooth Version) in an original modded chassis, with a ShtokCustomWork short pin PCB in the emitter. It takes a standard 5V 2.1mm plug for charging. LED switch for standard menu operation. A gazillion sound fonts (30 something) & effects. Certainly not a dueller in any sense of the word (no neopixel is) but a great cosplay / play-piece. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- Saberforge Forsaken (prior model)
- Modded Nexus Sabers (LGT) Xeno3Pixel core.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- External 2.1mm Recharge Port (wired for a 5v USB Charge cable)
- 12mm Illuminated Switch.
- High capacity Nexus 18650 cell (protected)
- This is a NON BLUETOOTH version of the board so you can't use it with the app.
-
Out of stock
A durable one piece design. This part can be used to combine various Adaptive Saber Parts or two Saberforge hilts together to make a staff. Available in a weathered finish. Length: 1.75in (4.445cm) -
Out of stock
A durable one piece design. This part can be used to combine various Adaptive Saber Parts or two Saberforge hilts together to make a staff. Available in a standard or weathered finish (standard pictured). Length: .8in (2.032cm) -
Sale!Out of stock
The hilt is machined by a professional blade smith, with tireless care given to every detail of it's construction, this saber is a work of art. -
Sale!
Max Forward Voltage 3.6V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator. -
Sale!
Max Forward Voltage 2.4V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
Out of stock
All-in-one STM32L4-based lightsaber electronics. It is small, feature-packed and 100% open source. This board retains all the features from the Teensy based designs, but are smaller and requires less work to put together. These are more advanced boards to use and it is recommended to read the detailed manual before use. Listing includes 1 x Proffieboard v2.2 and 1 x Micro SD Card. This is a new board with rolling updates. Board information and diagrams can be found here. These boards have been improved since the v1.5 and now has:Proffie Boards are both factory & SCF tested and confirmed 100% working prior to packing and shipping. When purchasing and installing a board, the customer does so at their own risk. Refunds will not be made for 'bricked' boards.- Breadboard compatible, no more tiny soldering pads
- Same size as before (1.3 x 0.7 inches)
- BATT- and GND are bridged by default (the bridge can be cut if desired)
- The components are a little farther away from the soldering pads
- The SD card sticks out more than before, hopefully making it easier to grab.
- FET pulldowns are grouned to BATT-, not GND
- Reverse polarity protection
- Beefier 5v power supply
- Able to completely cut power to the SD card (this *should* make deep sleep possible)
- The SD card power is also available on a pad, which could be used to cut power to bluetooth and displays during deep sleep.
- Uses resistor arrays to cut down on the number of components
- One less pad for neopixel data
- Neopixel LED Strip and Tri Cree LED Support.
- 44/22/11khz Audio.
- Touch Button Support.
- Multiple Blades And Effects With Different Presets For Each.
- Supports Both Monophonic and Polyphonic Sound Fonts
- Can Play Background Music With Other Sounds.
- Many Free Pins That Can Also Be Programmed For Other/Additional Features.
- Supports SmoothSwing! The Most Realistic Motion Algorithm For Sabers To Date!
- BATT+ – 2.6 to 4.5 volt input, drives everything except the LEDs
- BATT- – negative pad for LEDs, needs to be at same level as GND when both are connected. Note that there are two of them, which can be useful when driving many powerful LEDs.
- GND – ground for electronics except LEDs. Note that the two GND pads are interchangable and connected through the board.
- Button 1/2/3 – Hook up to closing buttons, or potentially touch buttons.
- Data 1 / ID – Normally used to measure the blade ID restor, and if it’s a neopixel blade, feed out neopixel data. For a fixed non-neopixel saber, it could be repurposed. Note that this pin has an internal 470 ohm resistor on it, so when hooked up to a neopixel blade, it does not need any resistors.
- Data 2-3 – additional neopixel data outputs, or free for other purposes.
- Data4/Dac – noeopixel data output, free, or audio DAC output
- LED 1-6 – Hooks up to negative side of LED (positive side of LED hooks up directly to battery.) These pads can handle up to 30 volts.
- SD Power – FET-controlled 3.3v. can be used to power down bluetooth and displays in low-power mode.
- SDA, SCL – these pins are used to communicate with the gyro and accelerometer chip.
- 5v – generated by the proffieboard, normally it’s only on when sound is playing.
- 3.3v – generated by the proffieboard.
- SWDIO, SWDCLK – can be hooked up to a ST-LINK device and lets you debug programs running on the proffieboard.
-
Plecter Labs Power Xtender™ Ver 2.0 Miniature electronic circuit designed to drive/switch a high load (LED, rumbling motor, relay) when the low voltage/current output from our electronic boards does not allow it. Drives for instance a 3.6V LED from a Blaster Core™ board or a luxeon from the Flash on Clash™ output of Crystal Focus™. Refer to the Petit Crouton user's manual for further details about the use of this module. NEW : Now with embedded SMD 2512 resistor footprint. Saves space when using the Power Xtender™ to drive the Flash On Clash ™. Use with 2 watt 2512 thick carbon film resistor. Dimensions : 0.55"x0.36" Input voltage : 0-5 volts max. Switches at 3.3V Output voltage/current : 12V / 1.5A -
Sale!
Max Forward Voltage 2.5V Max Current 1000mAh The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
-
## WORKS WITH ANY SABER USING A 2.1MM RECHARGE PORT & SINGLE LI-ION CELL ## This is the charger used to recharge an illuminated saber that has a 2.1mm recharge port in its electronic setup. It's a generic charger from an OEM supplier. We've sourced and tested these and they do the job nicely. Input Voltage : AC 100-240V (Worldwide AC Input) Input Frequency : 50-60Hz Output : 4.2V 1A 5.5mm*2.1mm Over Voltage Protection Over Heat Protection -
Micro Deans connectors. Same connectors used in Saberforge QC hilts. -
This is a seriously nice Mandalorian Vibroblade model. Printed in 2x parts, it assembles to 29.5cm in length. We print at 0.15mm layer height and 80% infill (for weight). At that size, it's a swift print of just under 6 hours on the machine. This is a bare plastic print which looks great but would also lend itself to additional cosmetic work.
How it Works
Whilst we're ultra-nerdy enough to run a fine suite of well maintained 3D printers, our CAD skills are a work in progress. We're predominantly a 3D printing service and only charge for machine time, which is usually only NZ$3.00 p.h.! Our little 3D print store is simply an example of some of the items we can print for you from well know sources such as www.ThingiVerse.com. It's a great source of 3D Printer files and we invite you to explore. If you see something you like, just come back to us for a print quote. ThingiVerse designs are covered by a range of different licenses from 'free to do what you want' Creative Commons licenses right through to 'non-commercial' clauses. For anything other than CC, we'll work with you to ensure no distribution licenses are breached (usually by simply asking the designer if we can print the item on your behalf). Easy as that. So if you're looking for a design we don't have listed as an example, just contact us.File Source
Files : www.thingiverse.com/thing:4004452 Designer : www.thingiverse.com/Filament_3d_Printing This item is covered by the Creative Commons - Attribution license We tip the designers! Even though the example designs we use fall under Creative Commons, we still like to give credit where credit is due so always endeavour to 'tip' the designer for their work via (for example) the ThingiVerse 'tip designer' feature. We aim for a 10% tip (or the nearest equivalent on the drop-down). If the designer doesn't accept tips, 10% goes to a local charity! -
This will hold most light sabers up to 4.5cm in diameter - the relief in the bottom portion is cut out to allow for wall mount power to your saber or for sound - the upper part will hold a 1" (25.4mm) blade securely enough that it wont fall out, but easy enough to take off the wall in case of Imperial entanglements. This is a bare plastic print.
How it Works
Whilst we're ultra-nerdy enough to run a fine suite of well maintained 3D printers, our CAD skills are a work in progress. We're predominantly a 3D printing service and only charge for machine time, which is usually only NZ$3.00 p.h.! Our little 3D print store is simply an example of some of the items we can print for you from well know sources such as www.ThingiVerse.com. It's a great source of 3D Printer files and we invite you to explore. If you see something you like, just come back to us for a print quote. ThingiVerse designs are covered by a range of different licenses from 'free to do what you want' Creative Commons licenses right through to 'non-commercial' clauses. For anything other than CC, we'll work with you to ensure no distribution licenses are breached (usually by simply asking the designer if we can print the item on your behalf). Easy as that. So if you're looking for a design we don't have listed as an example, just contact us.File Source
Files : www.thingiverse.com/thing:3023020 Designer : www.thingiverse.com/Elloel/about This item is covered by the Creative Commons - Attribution license We tip the designers! Even though the example designs we use fall under Creative Commons, we still like to give credit where credit is due so always endeavour to 'tip' the designer for their work via (for example) the ThingiVerse 'tip designer' feature. We aim for a 10% tip (or the nearest equivalent on the drop-down). If the designer doesn't accept tips, 10% goes to a local charity! -
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is an RGB Baselit Install. RGB installs are more durable when it comes to blade contact / duelling. Hilt:- KR Sabers Flagship in Tactical Black
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- Sabertrio Copper based heatsink and high performance XP-E2 Tri Cree LED
- Correct grade wire throughout
- Single 12mm non-illuminated red anodised switch. Saber runs single switch logic.
- Nix - 3D Printed Chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- KR Sabers 24mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- KR Sabers Flagship in Tactical Green
- Proffie V2.2 with approx' 8 quality, open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- Single KR Sabers 12mm Illuminated Cog Switch. Saber runs single switch logic).
- Goth3D - 3D Printed Chassis
- Chassis mounted kill switch
- High capacity 18650 cell (protected)
- KR Sabers 28mm Bass Speaker
-
This is a brand new saber expertly installed with carefully selected, complimentary quality components. One of the first of our lovingly installed KR Sabers Ready to Ship (RTS) range. Rather than having to wait the install queue, Ready to Ship sabers are all prepped and ready to go! This is a NeoPixel install. Neopixel installs are great for show and a little light choreography (at your own risk) but not durable enough for dueling. For models more suited to blade contact / dueling, make sure to look for our RTS RGB Baselit models. Hilt:- KR Sabers Flagship in Tactical Green
- Proffie V2.2 with approx' 12 quality open source sound fonts.
- ShtokCustomWorx NPXL V3 Hilt Side PCB Connector
- Correct grade silicon wire throughout
- KR Sabers Duoswitch. A PWR & AUX tactile switch combined into one 12mm 'rocker' design.
- 3D Printed Chassis
- High capacity 18650 cell (unprotected)
- KR Sabers 28mm Bass Speaker
