• Sale!

    Orange CREE XP-E LED / 3W

    Original price was: NZ$19.99.Current price is: NZ$9.99.
    Max Forward Voltage 2.5V Max Current 1000mAh The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
  • Plecter Labs Power Xtender™ Ver 2.0 Miniature electronic circuit designed to drive/switch a high load (LED, rumbling motor, relay) when the low voltage/current output from our electronic boards does not allow it. Drives for instance a 3.6V LED from a Blaster Core™ board or a luxeon from the Flash on Clash™ output of Crystal Focus™. Refer to the Petit Crouton user's manual for further details about the use of this module. NEW : Now with embedded SMD 2512 resistor footprint. Saves space when using the Power Xtender™ to drive the Flash On Clash ™. Use with 2 watt 2512 thick carbon film resistor. Dimensions : 0.55"x0.36" Input voltage : 0-5 volts max. Switches at 3.3V Output voltage/current : 12V / 1.5A
  • Out of stock
    All-in-one STM32L4-based lightsaber electronics. It is small, feature-packed and 100% open source. This board retains all the features from the Teensy based designs, but are smaller and requires less work to put together. These are more advanced boards to use and it is recommended to read the detailed manual before use. Listing includes 1 x Proffieboard v2.2 and 1 x Micro SD Card. This is a new board with rolling updates. Board information and diagrams can be found here. These boards have been improved since the v1.5 and now has:
    • Breadboard compatible, no more tiny soldering pads
    • Same size as before (1.3 x 0.7 inches)
    • BATT- and GND are bridged by default (the bridge can be cut if desired)
    • The components are a little farther away from the soldering pads
    • The SD card sticks out more than before, hopefully making it easier to grab.
    • FET pulldowns are grouned to BATT-, not GND
    • Reverse polarity protection
    • Beefier 5v power supply
    • Able to completely cut power to the SD card (this *should* make deep sleep possible)
    • The SD card power is also available on a pad, which could be used to cut power to bluetooth and displays during deep sleep.
    • Uses resistor arrays to cut down on the number of components
    • One less pad for neopixel data
    It retains it’s legacy features:
    • Neopixel LED Strip and Tri Cree LED Support.
    • 44/22/11khz Audio.
    • Touch Button Support.
    • Multiple Blades And Effects With Different Presets For Each.
    • Supports Both Monophonic and Polyphonic Sound Fonts
    • Can Play Background Music With Other Sounds.
    • Many Free Pins That Can Also Be Programmed For Other/Additional Features.
    • Supports SmoothSwing! The Most Realistic Motion Algorithm For Sabers To Date!
    Technical info:
    • BATT+ – 2.6 to 4.5 volt input, drives everything except the LEDs
    • BATT- – negative pad for LEDs, needs to be at same level as GND when both are connected. Note that there are two of them, which can be useful when driving many powerful LEDs.
    • GND – ground for electronics except LEDs. Note that the two GND pads are interchangable and connected through the board.
    • Button 1/2/3 – Hook up to closing buttons, or potentially touch buttons.
    • Data 1 / ID – Normally used to measure the blade ID restor, and if it’s a neopixel blade, feed out neopixel data. For a fixed non-neopixel saber, it could be repurposed. Note that this pin has an internal 470 ohm resistor on it, so when hooked up to a neopixel blade, it does not need any resistors.
    • Data 2-3 – additional neopixel data outputs, or free for other purposes.
    • Data4/Dac – noeopixel data output, free, or audio DAC output
    • LED 1-6 – Hooks up to negative side of LED (positive side of LED hooks up directly to battery.) These pads can handle up to 30 volts.
    • SD Power – FET-controlled 3.3v. can be used to power down bluetooth and displays in low-power mode.
    • SDA, SCL – these pins are used to communicate with the gyro and accelerometer chip.
    • 5v – generated by the proffieboard, normally it’s only on when sound is playing.
    • 3.3v – generated by the proffieboard.
    • SWDIO, SWDCLK – can be hooked up to a ST-LINK device and lets you debug programs running on the proffieboard.
    PLEASE NOTE: These boards are fully factory tested and approved prior to shipping. It is highly recommended to have a professional saber builder install this board. If you wish to install yourself; it is at your own risk. If you fry the board, it's on you. If there are any technical issues with the installation of the board please get in touch and we can forward you various information including groups and forums where troubleshooting can take place.
  • Sale!

    Red CREE XP-E LED / 3W

    Original price was: NZ$19.99.Current price is: NZ$9.99.
    Max Forward Voltage 2.4V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
  • Sale!

    Royal Blue CREE XP-E LED / 3W

    Original price was: NZ$19.99.Current price is: NZ$9.99.
    Max Forward Voltage 3.6V Max Current 1000mA The most suitable, closest available resistor will be linked below in the 'you may also like' section. You have a little leeway in choosing the correct resistance (due to how LEDs work). it's common to 'dither' the calculated value to the nearest commercially available value. You can always double check the exact resistor values by using our LED Resistor Calculator.
  • Heatsink module for 1" / 25mm ID tubes. Comes with centre hole and the 6x wire runs are milled to the edge of the copper heatsink.
  • Sale!

    SaberTrio In-Hilt Smart Charger 2.1mm

    Original price was: NZ$30.99.Current price is: NZ$29.99.
    ## WORKS WITH ANY SABER USING A 2.1MM RECHARGE PORT & SINGLE LI-ION CELL ## This is the charger used to recharge an illuminated saber that has a 2.1mm recharge port in its electronic setup. It has built-in safety functions including overcharging protection and an LED indicator to show when the battery is charging (red) or fully charged (green). It also features 4 interchangeable plug heads that are: Type A (US, Canada, Mexico, Japan, China) Type C (Europe, South America) Type G (UK, Malaysia, Singapore) Type I (Australia, New Zealand) The charger is designed specifically to recharge only 3.7V lithium ion batteries. Technical specifications : Input : 100 – 240VAC 50/60Hz 0.5A (max) Output : 4.2V 0.5A
  • The new NeoCree LED strip to Tri Cree RGRb XPE-2 conversion module. These have been designed and produced by Warsabers and ShtokCustomWorx to conveniently allow users to seamlessly convert their neopixel lightsaber builds, that use pogo pin PCB connectors, to an RGB ‘in-hilt’ LED system.  
  • This is the LONG pin option. Long pins are the standard choice unless you are installing in hilts with shallow emitters (i.e. thin neck models), where you would want a short pin version. If you are not already using a chassis with a dedicated recess, you will likely need a PCB holder AND a Lens Cover (to better support the pins. Kit comes un-assembled. You need to solder your own pins into the PCB. The manual can be found here.
  • This is the SHORT pin option. The long pin version are the standard choice unless you are installing in hilts with shallow emitters (i.e. thin neck models), where you would want this short pin version. If you are not already using a chassis with a dedicated recess, you will likely need a PCB holder. Kit comes un-assembled. You need to solder your own pins into the PCB. The manual can be found here.

Title